BLACKHAWK
 |
BLACKHAWK JIG (#303)
High strength, high impact aluminium extrusion. This jig is possibly the most durable and the most accurate on the world market. Alloy ends that attach to square steel centre tube eliminating twists even on uneven surfaces. The Blackhawk jig features adjustable stops in the arms that allow for the option of two or four point contact with the skate blade. This jig also offers blade height adjustment, adjustable rear end stops that maintain exact sharpening position every time. Net weight is 1.8 kg.
|
$229.00 Cdn
Phone Order
|
TITAN SHARPENING
 |
TITAN SHARPENING JIG (#005)
Light to carry, quick to assemble and easy to use. Versatile and strong, this jig converts easily to all blade sizes. High Density structural alloy extrusion. Features alloy ends that attach to square steel center tube, eliminating twist, especially on uneven surfaces. Its net weight is 1.7 kg. An ideal choice when sharing with others. Great value for your money!
|
$190.00 Cdn
Phone Order
|
ZANDSTRA ST LOUIS
 |
ZANDSTRA ST.LOUIS TABLE TOP JIG
Precision sharpening jig for accurate adjustment of the skate. The blade is clamped in place along its entire length. Suitable for virtually all straight blades. If you skate with a bent blade don't use this jig. Complete with precision sets for the top. This is the only jig that holds the Zandstra moulded boots.
|
$185.00 Cdn
Phone Order
|
NORTON COMBINATION
 |
NORTON COMBINATION OIL STONE
1"x2 1/2"X11 1/2" double-sided oil sharpening stone to use with all blades. Great sharpening stone for the beginner and the world champion. This is a time tested favourite. Great life span! Will outlast most skating careers.
|
$60.00 Cdn
In Stock
|
DIAMOND
 |
DIAMOND COARSE SHARPENING STONE
When you need to hand adjust your rocker or get a burr in no time try the coarse cutting stone. Be sure to use a fine stone and finishing sandpaper triangle to get a good smooth polished finish. 250 Grit. Size 2.5" x 11.83"
|
$85.00 Cdn
Phone Order
|
DIAMOND
 |
DIAMOND FINE SHARPENING STONE
Millions of diamond cutting crystals are permanently bonded with a stainless steel alloy to make up the Diamond sharpening stone. Can be used on all blades to get a great sharp blade. 600 Grit. Size: 2.5" x 11.38"
|
$55.00 Cdn
In Stock
|
DIAMOND
 |
DIAMOND MEDIUM SHARPENING STONE
Millions of diamond cutting crystals are permanently bonded with a stainless steel alloy to make up the Diamond sharpening stone. Can be used on all blades to get a great sharp finish. Will cut a bit faster than the fine diamond stone. 400 Grit. Size: 2.5" x 11.38"
|
$55.00 Cdn
In Stock
|
NORTON
 |
NORTON BURR STONE
Approximately 4" and 3/4". A must for all skaters. Put that fine edge on your skates.
|
$10.00 Cdn
Phone Order
|
LAS MISTRAL
 |
LAS MISTRAL HELMETS
This helmet meets the requirements for International racing and for racing in the USA. This helmet has just been improved!! It now has a better and stronger exterior shell. Its unique velcro fastening system makes it a one size fits all. Meets ISU Rule # 294
|
$85.00 Cdn
In Stock
|
DURABULL
 |
DURABULL GLOVES
Canadian made DuraBull gloves offer protection for the short track skater. Unlined and made with steerhide, these gloves come in sizes 7 to 12. Tan or Black colours only. What size do I need? Just measure from the tip of your longest finger to the starting point of your wrist and the measurement in inches is your size. Simple eh!
|
$10.00 Cdn
In Stock
|
VIKING
 |
VIKING GLOVES
The Viking Gloves are available in the colour navy only, with light-grey leather on the side. Sizes 5 - 12 (also half sizes)
|
$32.00 Cdn
Phone Order
|
DIAMOND
 |
DIAMOND MINISHARP WITH KEY RING
The anytime, anywhere sharpener with flip open handle and key ring. This lightweight 600 grit diamond whetstone measures approximately 4 inches by 1 inch and is only a quater inch thick. Ideal for removing the burr off you blades. Award-winning design.
|
$5.00 Cdn
Short Supply
|
BLADE
 |
BLADE BENDER
Designed to be the best short track blade bender in the world! Easy grip handle enhances the leverage for ease of operation. The hard rubber concave contact tire ensures a great bend. The self-holding blade supports slide to allow for custom bends. Easy, adjustable stop for speedy and accurate use. The deflection and rebound can be measured with the gauge to make micro adjustments.
|
$300.00 Cdn
Phone Order
|
ULTIMATE
 |
ULTIMATE EDGE JIG
For your ultimate performance. Great for Short and Long Track Blades. All aluminum construction; lightweight. Completely anodized for corrosion resistance. All milled surfaces. Quick release blade clamps; quick release blade vertical locators. Stainless steel bolts and threaded inserts. Screwed-on rubber feet. Available in Enriched Blue with Gold Trim. Nothing sharpen better than the Ultimate Edge Jig!
|
$275.00 Cdn
In Stock
|
MAPLE
 |
MAPLE DIAL GAUGE
For precision measuring of radius and bend. Comes with instructions and a conversion table.
|
$150.00 Cdn
In Stock
|
ZANSTRA
 |
ZANSTRA MOULDED SKATE
A great entry level skate for the young speed skater. The plastic moulded boot with a foam liner provides excellent support and is very warm and comfortable. The blade is permanently riveted to the boot. A Zanstra St. Louis Tabletop Jig is required for sharpening.
|
$299.00 Cdn
In Stock
|
MAPLE
 |
MAPLE SHORT TRACK BOOTS
Fully heat moldable for perfect fit, these boots are either glass or carbon fibre with rhenoflex shell construction and pigskin lining.
|
$200.00 Cdn
In Stock
|
LAPEL
 |
LAPEL PINS
Silver or gold lapel pin of a speed skater. Grip fastener. (Approximate height: 1")
|
$5.00 Cdn
In Stock
|
PLAQUE
 |
PLAQUE FOR CUTTING EDGE PINS
This very distinctive plaque holds all the pins from CASSA's Cutting Edge Skills program (see CAT #5105). The plaque can be mounted on the wall or placed on a stand (included) to display on a table top or dresser.
|
$20.00 Cdn
In Stock
|
MAPLE
 |
MAPLE LONG TRACK BOOT
This is a fully heat mouldable boot for a perfect fit. The bottom portion of the boot is made out of carbon fibre for superior strength. The boots come with 6.5 inch spacing to attach your blades.
|
$200.00 Cdn
In Stock
|
NAGANO
 |
NAGANO ALLROUND
The klapskate-version of the Viking Allround: The Viking Allround boot mounted on a Nagano Special klapskate (tube and blade of the Special quality). A combination of the form-fitted and conventional boot. The counter is thermoplastic. The bottom has a built in orthopedic arch support, to give a better fit. The fit of this boot and the Viking Gold is similar to the famous Viking Special. The boot is made of kangaroo-leather and comes with a built in ankle piece. Tube and blade are of the Special quality. Size 35 - 46.
|
$650.00 Cdn
Short Supply
|
NORTON
 |
2x1 India Stone
|
$10.00 Cdn
In Stock
|
BONT
|
Bont Jet Boot and Sonic 1000 Blades
|
$350.00 Cdn
In Stock
|
Pass
 |
PASS p400
Vacuum-formed heat moldable carbon shell.
Fastback contour at Achilles tendon to relieve pressure. Padded heel, ankle and calf area. Dual mounts front and rear. Standard colour blue and white.
|
$550.00 Cdn
In Stock
|
Pass
 |
PASS p250
Vacuum-formed moldable shell with padded heel, ankle and cuff. Dual mounts.
|
$380.00 Cdn
In Stock
|
Pass
 |
PASS p251
Fibreglass shell, vacuum-formed heat moldable, padded heel ankle and calf area. Dual mounts front and rear. Standard colour red and white.
|
$495.00 Cdn
In Stock
|
Pass
 |
PASS PCB05 Club Boot
Vacuum-formed heat moldable with leather upper, suede lining. Standard colour black & yellow with dual mounts. Lace cover and buckle extra.
|
$395.00 Cdn
In Stock
|
APEX
 |
APEX Short Track
These custom made boots, manufactured by Olympic medallists Mathieu Turcotte and Fredrick Blackburn are used by the top speed skaters in the world. Includes fully molded tongue; removable ankle ratchet buckle; fitted lace cover and laces.
|
$1,000.00 Cdn
In Stock
|
MAPLE
 |
MAPLE Short Track Boots
Fully heat mouldable for perfect fit, these boots are either glass or carbon fibre with rhenoflex shell construction and pigskin lining.
|
$200.00 Cdn
In Stock
|
BONT
 |
BONT GT SPEC R Short Track
Bont developed the GT Series of blades with design input from some of the world's top skaters. Includes a 7000 Series aluminum frame, powder-fused tool steel blade, hardened blade to 64 Rockwell, standard 9 meter radius blades, 18" maximum length, and carbon fiber cups. The blades can be ordered straight or machine bent and come in standard thickness of 1.0, but we offer from 0.9 to 1.5 with almost any radius and bend you desire.
|
$559.00 Cdn
In Stock
|
BONT
 |
BONT GT SPEC A Short Track
Bont developed the GT Series of blades with design input from some of the world's top skaters. Includes a 7000 Series aluminum frame, high carbon steel blade, tumble polished, standard 8 meter radius blades, 18" maximum length, and carbon fiber cups. The blades can be ordered straight or machine bent and come in standard thickness of 1.0, but we offer from 0.9 to 1.5 with almost any radius and bend you desire.
|
$356.00 Cdn
In Stock
|
BONT
 |
BONT Sonic Series 7000
7000 Series aluminum frame
* Powder-fused tool steel blade
* Blade hardened to 64 Rockwell
* Blades come with standard 8 meter radius
* Space age bracket design
* Blades can be ordered straight or machine bent
* Blades come in any thickness with almost any
radius and bend you desire
|
$495.00 Cdn
In Stock
|
BONT
 |
BONT Sonic Series 1000
High performance entry level blade
* Blade 60-62 Rockwell
* Standard 1mm thickness
* Maximum length 16"
* Exceptionally fine gliding blade
* Standard aluminum brackets
, Blades come with standard 8-meter radius
|
$220.00 Cdn
In Stock
|
EXCALIBUR
 |
EXCALIBUR II
High strength, lightweight, computer designed alloy extrusion with off-centre blade mounting. Blade lengths, 15"-17.5" in 0.5" increments. Includes mounting hardware and angles.
$375 Factory Bend Option add $10
|
$375.00 Cdn
In Stock
|
PENNINGTON
 |
PENNINGTON KATANA
|
$425.00 Cdn
In Stock
|
PENNINGTON
 |
PENNINGTON AVENGER
Frames are made from single piece alloy with angle attachment bracket. Lengths available are: 12" blades for boot sizes up to size 1, with the 5-1/2" bolt centres. 14", 15", 15.5", 16", 16.5" and 17" lengths for the other boot sizes. Hardwearing steel blade. All blades are pre-radius ground and supplied with structural alloy angle brackets, high tensile bolts and shakeproof nuts.
|
$275.00 Cdn
In Stock
|
PENNINGTON
 |
PENNINGTON EXTREME Sprinter Bi-Metal
Designed with the sprinter in mind as the bi-metal adds strength with the additional height for cornering.
High profile bi-metal
|
$390.00 Cdn
In Stock
|
MAPLE
 |
MAPLE GOLD Short Track
Bi-metal (64 Hrc) blade with gold coloured anodized 7000 series cups and tubes.
|
$365.00 Cdn
In Stock
|
MAPLE
 |
MAPLE SUPERFLEX Short Track
For extra flexibility, the Superflex is a bi-metal (64 Hrc) with red anodized 7000 series aluminum tubes and cups.
|
$375.00 Cdn
In Stock
|
MAPLE
 |
MAPLE MAD DOG
A patented design based on sophisticated mathematics for optimum force distribution across the tube. The mounting cups can be adjusted in height. Bi-metal runners (62-64 Hrc). Blade thickness: 1.10-1.18 mm -*- 1.25 to 1.30 mm. Cups and tubes are anodized 7000 series aluminum. Titanium colour anodized tubes and red cups.
|
$410.00 Cdn
In Stock
|
MAPLE
 |
MAPLE PREMIUM Short Track Blades
This special junior design is made of chrome steel (60 Hrc) 1.2 mm thick and has gold coloured anodized 7000 series aluminum tubes and standard aluminum L cups.
|
$185.00 Cdn
In Stock
|
NUTS
 |
Nuts & Bolts for PROTÉGÉ Blades
Hardware is specifically for Protégé Blades.
|
$15.00 Cdn
In Stock
|
T-CUPS
 |
T-Cups (Set of 4)
The newest cups for attaching short track blades. Specify the type of Boot they are to fit. Fits all blades.
|
$65.00 Cdn
In Stock
|
BRACKETS
|
L Brackets (Set of 4)
Metal alloy cups for attaching short track blades. Specify the type of boot they are to fit. Fits all blades.
|
$60.00 Cdn
In Stock
|
NUTS
 |
Nuts & Bolts for EXCALIBUR II Blades
Hardware specifically for the Excalibur II Blades. It’s always a good idea to have an extra package around.
|
$15.00 Cdn
In Stock
|
| Back to top |
